Tell CME the pole count, pitch, operating current and voltage, and wire gauge. We'll help you select the right block and prepare a B2B quote.
Send a quote request →Pluggable or fixed — the difference is in what disconnects
A fixed (modular) PCB terminal block is a single part mounted directly to the board, into which wires are screwed or clamped permanently — to disconnect the harness from the board, every terminal has to be unscrewed individually. A pluggable block is a two-part system: the male half (a pin header) is permanently mounted on the board, and a female plug carrying the wire terminations connects to it and disconnects in one motion — without touching individual terminals. In service and production this matters: a pluggable block lets you swap an entire board or module in seconds, while a fixed block requires unwiring the harness every time.
Specs by product family
| Type | Pitch | Poles | Current | Wire gauge |
|---|---|---|---|---|
| Pluggable PCB | 3.81 / 5.08 / 7.62 mm | 2–25 | 8–16 A | 0.25–2.5 mm² |
| Modular (fixed) | 3.81–10.16 mm | 2–3/module* | 8–76 A | 0.25–16 mm² |
| Push-in spring | 5.08 mm | 2–12 | 10–16 A | 0.25–1.5 mm² |
| Pluggable rail-mount | 5.08 mm | 2–25 | 16 A | 0.25–2.5 mm² |
*Modular block modules interlock to build any pole count — this isn't a 2–3-terminal limit on the whole block. Rated voltage: 250–400 V for the pluggable families, up to 800 V for the modular family (depending on pitch and cross-section).
Screw vs push-in spring clamp
Most families in the range combine a screw clamp with a spring — the screw provides steady pressure on the conductor regardless of vibration, while the spring compensates for small changes in insulation over time. A separate family — push-in spring terminal blocks — removes the screw entirely: the wire is pushed directly into the clamp with no tool, and released with a lever or release tool. This is faster for serial assembly, but covers a narrower cross-section range (up to 1.5 mm² in CME's range) than the screw families.
Assuming "modular" PCB terminal block means the same thing as "pluggable." A modular block is built from interlocking segments (2–3 poles each), which lets you build any length of block — but the wires are still clamped directly into parts mounted permanently to the board. It is not a detachable system the way a pluggable block (header + socket) is. If a project needs to disconnect the whole harness quickly without unscrewing terminals, the pluggable family is the right choice, not the modular one.
Standards
The screw and screwless clamping units used in PCB terminal blocks fall under IEC 60999 (EN 60999/VDE 0609). The safety of connecting devices (clearance and creepage distances) is covered by UL 1059, which classifies connection technologies into use groups (industrial equipment is typically assessed under use groups C/D). PCB terminal blocks, including feed-through types, fall within the scope of IEC 60947-7-4, and PCB connectors within IEC 61984 — with the caveat that PCB plug-in connectors themselves don't have one dedicated construction standard and are tested against the applicable general standards. Compliance documentation for a specific part number is available on request.
What's available from CME
CME distributes the full Mega Radar range of PCB terminal blocks and connectors: pluggable PCB terminal blocks, pluggable connectors, pluggable rail-mount terminal blocks, modular PCB terminal blocks, spring-clamp PCB terminal blocks, plus mounting accessories — DIN rail mounting brackets, plastic PCB spacers, DIN rail PCB holders, and complementary and custom-made products.
Housing colors (blue, green, orange, grey, black, red) allow circuit coding on the board. Operating range for most families: -40°C to +100°C.
What to prepare for your quote request
- Pole count and pitch (pin spacing) required by the PCB design.
- Operating current and voltage of the circuit.
- Wire gauge and preferred clamp type (screw or push-in).
- Whether a pluggable (detachable) or fixed version is required.
- Planned quantity and delivery schedule.
Frequently asked questions
Is a pluggable terminal block more expensive than a fixed one?
Usually yes, because of the extra part (socket plus plug instead of one block) — but it saves service time when swapping modules. We'll prepare a quote for your specific configuration on request.
Can I join segments of a modular block to get a custom pole count?
Yes — that's the defining feature of the modular family: 2–3-pole segments join into any length.
Can push-in clamps handle larger wire cross-sections?
In CME's range, the push-in family covers up to 1.5 mm² — for larger cross-sections, the screw or modular family is the better fit.
See also the full CME PCB terminal blocks category.